Loading...

Home > Hard Drive > Plugging Hard Drives Into To Optical Drives' IDE Cable?

Plugging Hard Drives Into To Optical Drives' IDE Cable?

Contents

Slide the drive into an available slot and find 2 or 4 case screws. BUY NOW FREE TRIAL PARTNERS Partners Become a Partner Locate a Reseller Partner Programs > How to > Computer Instruction > Install IDE Hard Drive Install IDE Hard Drive 2016-08-05 Re-check your cabling (both data and power cables). You plug one end of the data cable into the drive and the other end you plug into the motherboard. navigate here

That's not always true. If your using Windows 9x (why?) then you'll want to check out bootdisk.com and find something that'll cover your needs. If you use that drive under its original letter to install software, that software will later attempt to access the drive using the old drive letter. Choose one of the power cables coming from the power supply and press the Molex connector onto the drive power connector, as shown in Figure 8-6.

How To Connect Ide Hard Drive To Sata Motherboard

Would you like to tell us about a lower price? Flag as duplicate Thanks! There was an error retrieving your Wish Lists. Advice from Jim Cooley Reinstalling or updating the chipset drivers may also enable (or re-enable) DMA support for the optical drive under Windows 2000 or XP.

  1. A couple of things to consider though: 1.
  2. It requires manufacturers to provide owners and independent repair businesses with fair access to service information and replacement parts.
  3. I highly recommend this not only to recover data but if you have a hard disk around now you can use it without to buy an enclosure.
  4. If the cable isn't long enough to give you some working slack with the drive outside the case, detach the cable from the motherboard and connect it just as you would
  5. IDE cable (if required).
  6. Tell them repair is good for farmers, good for consumers, and good for businesses.
  7. When you want to boot to the second hard drive's OS, go to the boot options on your computer and choose the drive.
  8. Keep the drive in the protective anti-static container until ready to install.

Hard disks have passed through a long evolution of connectivity and data transfer standards. But if it is a standart desktop PC it should not matter wich IDE port you use for your harddrives or optical drives gfxrelay, Aug 8, 2008 #4 Ben B Reply Adam August 24, 2016 at 3:49 pm @MikeTek the middle connector is the master, the end is the slave. How To Connect Ide Hard Drive To Motherboard Enabling Bus Mastering (DMA) support¶ Some older ATAPI optical drives operate in Programmed I/O (PIO) mode rather than Direct Memory Access (DMA) mode, which is also called Bus Mastering mode.

Make sure there is space available in the cage for another drive. Ide Hard Drive Jumper Settings Since most of people are using Windows 2000 or XP, so overleap all the steps in fdisk. Pentium IV's and earlier computers used the IDE drive standards. http://www.tomshardware.com/forum/293991-32-plug-cables-optical-drive-hard-drive Wire 20 is not connected to anything.

We are not responsible for them in any way. Sata And Ide Hard Drives Together It requires manufacturers to provide owners and independent repair shops with access to repair information and replacement parts—so you have the resources you need to fix things quickly and affordably. All Ultra ATA/66 devices should be attached to a single channel and devices that do not support Ultra ATA/66 should be connected to a separate channel. We have a chance to help the environment and stand up for local repair jobs—the corner mom-and-pop repair shops that keep getting squeezed out by manufacturers.

Ide Hard Drive Jumper Settings

Good thing that it happened while I was right there! view publisher site Setting the Jumpers Master or Single Drive - Use this setting if the drive is the only drive on the ATA interface cable. How To Connect Ide Hard Drive To Sata Motherboard Newer Than: Search this thread only Search this forum only Display results as threads Useful Searches Recent Posts More... How Many Hard Drives Can Be Connected To A Single Ide Cable Yes No Cookies make wikiHow better.

You will need to know whether to buy an IDE or SATA drive, and you should be able to tell by looking at the cables. http://swiftinv.com/hard-drive/plugging-in-a-new-hard-drive.html If you are unable to get your drives working using the current configuration, try other configurations as explained here Note that the BIOS Setup will also tell you the number of and they work! Your Recently Viewed Items and Featured Recommendations › View or edit your browsing history After viewing product detail pages, look here to find an easy way to navigate back to pages Why Is It Necessary To Partition The Hard Disk While Installing Operating System?

Assigning the highest available drive letter, Z, to the optical drive prevents Windows from ever altering that drive letter. The other drive or Slave drive was for data storage. The cable length will affect your choice too, as IDE cables are usually quite short. his comment is here Master should be selected if this will be the only device on a single IDE cable or if it is the second device to be connected and the other device is

Simple white-plug / black-plug converters can solve your power plug compatibility issues: Compatibility Plugs (Wikipedia) One drive integration technique uses your computer's USB port to connect an incompatible disk drive. Ide Cable Select Gift-wrap available. Subscribe to Our Newsletter Email: Advertisement Scroll down for the next article © 2017 MakeUseOf.

Advertisement On the motherboard end, the socket looks like this.

Now figure out where your additional drive is going to go. On the edge of one of the cables you will see a line. When your tractor breaks or your cell phone stops working, they want to be the only people who can fix it. How To Connect Ide Dvd Drive To Sata Motherboard If you're not already familiar with forums, watch our Welcome Guide to get started.

Remove an old IDE drive After removing the covers the next step is to locate and remove the data and power cables attached to the old device. Yes No Not Helpful 0 Helpful 0 Where can I buy a split cable for SATA hard drives? Take Action It's time to speak out for your right to repair Dear Minnesotans, Minnesota has a chance to become the first state in the nation to pass "Fair Repair" legislation. weblink On rare occasions you'll run into a system with the drives packed so tightly they lack sufficient clearance.

The data cable is labelled A and the power cable is labelled B. HARDWARE SOFTWARE INTERNET PC UPGRADING PC MAINTENANCE DICTIONARY GAMING How to install a CD/DVD writer | SATA and IDE drives Whether you are installing a new optical drive into your computer's If this is a secondary drive then you're obviously after pure storage space so just make it a primary partition and allocate 100% of your space to it. Yes No Not Helpful 1 Helpful 10 If I already have data in the second hard disk, will it all be gone when I format it?

Parama Herath If you have an empty PCI slot, you can buy a SATA card and attach other SATA drives to that. Order it now. BUY NOW FREE TRIAL Data Recovery Wizard for Mac Best Mac data recovery software recovers whatever you lost from Mac machines & storage devices. The final photo shows the back of an IDE disk drive.

This is where you want to put an IDE drive into a SATA-only motherboard or vice versa. Sure enough, the BIOS shows two devices loaded and functional. Can I put my brand new CDROM Burner on the Slave position on my 80-wire cable?