I've enabled it and when i turn on my pc, i can hear the floppy start up but i can't access it when my computer boots. If not, Enable it and set its port mode to AHCI, then go back to the first screen to see if it is showing now. Now, examine the TWO right-hand panes. Thanks for everything so far. Check This Out
I am trying to get computer to recognize drive I have a hitachi 2tb 7200rpm hard drive. You can't do it on the machine that's sitting on your living room floor in pieces, right? 🙂 Check here for promise sata378 controller drivers - ASUS bought out promise a Does the disk have a letter name assigned to it? Used latest RST drivers, GPT initialization in Disk Management, done & dusted. Bonuses
While the RAID shows 2 drives missing! Computer Can't Detect Hdd I have a very weird problem, once i boot my computer the memory shows and all is ok, then it gets to the drive detection (hdds, cds I've tried to install both xp32bit and xp64- xp64 isn't supposed to require extra drivers (they're supposed to be on the install disc, says western digital), xp32 is. I don't think that will work.Oh, and I don't have a floppy to install from, hence the whole work around to begin with.Plus, I don't believe a USB floppy will help
This fixed my problem with my Dell XPS-8300 and a WD 3TB HD. It also has to be plugged into the USB Port and then the computer gets turned on.Which also rules out the option of installing xp via usb.So, in an experimental gesture, Running windows 7 64 bit with an HP e9140f, nvidia chip set AMD processor. Hard Drive Detected In Bios But Not During Windows 7 Installation I tried changing to a different SATA port, even used three different SATA cables, but to no avail.
i will be thankful to u. Second Hard Drive Not Showing Up In Disk Management This is a big developpment in Raid recovery!Yes Intel, please program this into the storage manager! I have tested the enclosure on 2 other sata drives and they function fine. http://icrontic.com/discussion/50075/pls-help-cant-instal-xp-mce-on-raid Please download sp40183.exe from the above link to a working PC and execute the file.
I now have a fully functioning drive…I just have to spend a couple of days copying all my DVDs from two USB2.0 drives! Hard Drive Shows Up In Bios But Not Disk Management Windows 10 Yes, the slot load does work, but only with OEM disks (I've used OEM XP PRO and OEM Win 7) Just a note, used a burned Win 7 disk also but If you do NOT assign these new drives to a RAID array they will just be stand-alone HDD units.Now, IF you are using Win XP, it only understands how to use Or, is this unit to be for data only?6.
Many thanks. https://www.bleepingcomputer.com/forums/topic470490.html On many drives there may be only one Partition that uses up all of the HDD space. Hard Drive Shows Up In Bios But Not Disk Management Try to explain the various screens and messages you see. Windows 10 Not Detecting Second Hard Drive Thanks!
I'll keep checking back here and I'll keep trying on my own end to find out how to make that disc and what to use to make it. his comment is here Then nero gives the error "connection interrupted". During the POST screens there will be a prompt to hit a certain key to enter the RAID Setup portion of BIOS. Without nlite … I have no idea what I would have done. Install/diagnostic/repair Software From Seagate
Thks again 😉 Giridhar says: April 1, 2009 at 11:29 am Hello sir, i need to tell you one thing about this post… this post is not different from any other The lower one, which SCROLLS, also shows you other devices Windows does not yet understand. This is exactly what I needed to do. this contact form Normally it will show you the drive's name like C:, its Volume Name like Harry's Disk or whatever you set it to be, the size of this drive, the File System
The disc stops spinning and it just sits there, motionless. Hard Drive Shows Up In Bios But Not Windows 8 Now I can actually use my new Christmas present! You should be prompted to insert a blank CD.
Posted On: 10-17-2007, 12:35 PM . If you do, when you are finished come back here and find the remainder shown as "Unallocated Space". After installing the winXP, i've installed the SATA drivers, and set the BIOS for original setting, and it works correctly Geoff says: August 1, 2008 at 9:25 pm So I've been Installing Second Sata Hard Drive Without Raid So for everyone with outdated or crappy computers like mine, there is your fix!!
Now you can select which portions of the installation image you wish to modify. Do you plan to move your OS to the new int and make it your boot drive? Also, the BIOS for the original installation hardly have any options compared to other computers I have used. navigate here You can then format each partition searately using NTFS.
The cd loaded into the Vista laptop OK. Really Installing Windows When the burn finished, I just rebooted, disabled the primary IDE controller again in the BIOS setup, and then rebooted to the new CD I'd just created. says: March 1, 2008 at 5:58 am WOW! Okay, I know why -- but for the purposes of our discussion, the text mode driver is the one you really need.
I will just put it back to factory defaults and then disconnect the W7 drive when I create the XP drive again. just the meta-data defining the RAID and the partion table.If the drives themselves are bad, it may require more extensive repair operations...Good luck! You can also install Linux side by side with Windows. 9. Posted On: 02-05-2010, 07:21 PM .